CineLR 7 6S O4 HD

Description

The CineLR 7 O4 6S HD is a 7.5-inch long-range cinematic BNF drone designed for smooth cruising, clean DJI O4 footage, high-capacity battery setups, and easy maintenance.

It combines an H-shaped frame design, DJI O4 Air Unit Pro, BLITZ F7 Flight Controller, BLITZ E55 4-IN-1 ESC, XING2 2809 1250KV motors, pre-installed GPS, quick-release side panels, LED control module, front-mounted O4 Air Unit, and a fixed rear XT60 battery plug.

This drone is designed for experienced FPV pilots who want a 7.5-inch long-range cinematic platform with reduced propeller view, strong 6S performance, and practical field maintenance. It is not a complete Ready-to-Fly set and still requires compatible goggles, radio controller, battery, charger, and setup checks before the first flight.

Highlights

Innovative H-Shaped Long-Range Frame Design
The CineLR 7 uses an H-shaped frame layout designed to reduce propellers in view while keeping the platform suitable for smooth long-range flying and cinematic footage.

This makes it a practical choice for pilots who want cleaner DJI O4 video from a 7.5-inch platform without moving to a full cinelifter or heavy X8 setup.

7.5-Inch Long-Range Platform
The CineLR 7 is designed for efficient 7.5-inch cruising, cinematic long-range routes, mountain flying, coastal flying, and high-capacity battery setups.

Compared with 5-inch FPV drones, the larger 7.5-inch platform can carry bigger batteries and is better suited for endurance-oriented flying, but it also requires more careful battery management, route planning, and wind awareness.

Quick-Release Side Panels
The quick-release side panels help protect internal electronics from debris and make maintenance easier. They also help keep the build cleaner by reducing exposed wiring and cable clutter, while still allowing access for inspection, repairs, and service work.

DJI O4 Air Unit Pro – HD Recording and Digital FPV
The DJI O4 Air Unit Pro provides high-quality digital FPV video and onboard recording.

With its 1/1.3-inch image sensor, 155° ultra-wide field of view, D-Log M support, RockSteady 3.0+ stabilization, 1080p/100fps live view, and up to 4K/120fps onboard recording capability, the O4 Air Unit Pro is well suited for cinematic long-range footage.

Up to 25 Minutes Manufacturer-Stated Hover Time
The manufacturer states up to approximately 25 minutes of hover time with a 21700 6S 8000mAh Li-Ion battery under iFlight laboratory conditions.

High-Performance BLITZ F7 Stack
The CineLR 7 uses a BLITZ F7 Flight Controller together with a BLITZ E55 4-IN-1 2–6S 55A ESC. The electronics system is designed for stable 6S operation, larger 7.5-inch propellers, and long-range flight requirements. The ESC offers up to 65A burst current according to manufacturer information.

Built-In GPS Module
The CineLR 7 includes a pre-installed GPS module with protective TPU cover. GPS can support coordinates, telemetry, flight logging, and Betaflight GPS Rescue after correct configuration and testing by the pilot.

Important: GPS Rescue is not enabled by default and must not be treated as a guaranteed return-to-home function. It must be configured, checked, and tested carefully before use.

Fixed Rear XT60 Battery Plug
The rear-mounted fixed XT60 battery plug helps with cleaner cable routing and reduces the risk of battery leads reaching the propellers. This layout also supports better battery cable management on larger long-range battery setups.

Front-Mounted DJI O4 Air Unit
The front-mounted Air Unit layout improves cooling access and keeps the DJI O4 Air Unit Pro easier to service. This helps support stable O4 operation during longer flights and makes SD card access more practical.

LED Control Module
The CineLR 7 is equipped with a BLITZ LED Control Module. The LEDs are not configured through Betaflight. They can be adjusted directly through the LED control module buttons, depending on the installed configuration.

BNF Factory Setup

This drone is delivered as a BNF, which means Bind-and-Fly.

It is assembled, factory configured, and tested before shipment. However, BNF does not mean Ready-to-Fly. The drone still needs to be bound to a compatible radio controller before the first flight.

Before the first flight, check all screws, motor direction, propeller orientation, receiver binding, failsafe behavior, GPS status, video link, OSD, Betaflight modes, and voltage warning settings.

ReadyFly Kits – Complete FPV Sets Available

This product is sold as a BNF drone.

BNF means Bind-and-Fly: the drone is assembled, tuned, and equipped with the selected receiver and DJI O4 video system, but it still needs to be bound to a compatible radio controller before flight.

If you need a complete FPV setup, we also offer ReadyFly Kits or compatible accessory bundles in our shop. These make it easier to combine suitable goggles, radio controller, batteries, charger, propellers, and accessories.

Choose this BNF drone if you already have compatible DJI O4 FPV equipment and a matching radio system.

Choose a ReadyFly Kit or accessory bundle if you want a more complete FPV setup.

Required to Fly

This is a BNF drone, not a complete ReadyFly Kit.

You also need:

• Compatible DJI FPV goggles
• Compatible radio controller matching the selected receiver version
• Suitable 6S battery
• 6S-compatible LiPo/Li-Ion balance charger
• microSD card for onboard recording, if required

Not included with the BNF drone:

• Battery
• Charger
• FPV goggles
• Radio controller
• microSD card
• Action camera

Choose the Correct Receiver Version

Please choose the receiver version that matches your radio controller.

Available receiver versions:

• For DJI FPV Controller 2 & 3
• TBS Crossfire Diversity NANO RX
• iFlight ELRS 2.4GHz True Diversity RX
• iFlight ELRS 868/915MHz True Diversity RX
• iFlight ELRS 2.4GHz / 868 / 900MHz Dualband Diversity RX

The DJI O4 Air Unit Pro is responsible for video transmission. The selected receiver/control version determines how the drone receives control commands from your radio controller.

DJI Controller Version
Choose the DJI Controller version if you want to control the drone with DJI FPV Remote Controller 2 or DJI FPV Remote Controller 3.

This version is configured for DJI SBUS control. The DJI Controller version does not have additional receiver antennas because the control signal is transmitted through the DJI O4 Air Unit Pro system and its O4 antennas.

Important: The DJI Controller version is intended for DJI remote control use. If you want to use ELRS or TBS Crossfire later, a separate receiver must be installed and configured correctly. This may require wiring changes, disconnecting DJI SBUS, or using another UART.

TBS Crossfire Diversity NANO RX Version
Choose this version if you use a TBS Crossfire radio system or a compatible Crossfire module and want the Crossfire Diversity receiver variant.

This version uses two receiver antennas.

ELRS True Diversity 2.4GHz Version
Choose this version if you use an ELRS 2.4GHz radio controller and want the True Diversity receiver variant.

This version uses two shorter 2.4GHz receiver antennas.

ELRS True Diversity 868/915MHz Version
Choose this version only if your radio controller or external module supports ELRS 868/915MHz and you want the True Diversity receiver variant.

This version uses two longer 868/915MHz receiver antennas.

ELRS 2.4GHz and ELRS 868/915MHz are not compatible with each other.

ELRS Dualband Diversity Version
Choose the ELRS Dualband Diversity version only if your radio hardware and ELRS setup support the required dualband configuration.

This version is designed for pilots who want one receiver system with dualband capability and diversity reception.

Receiver Antenna Note

All ELRS and Crossfire Diversity receiver versions use two receiver antennas.

The DJI Controller version does not have separate receiver antennas because control is handled through the DJI O4 Air Unit Pro antennas.

Product images are for display and reference only. Some images may be generic manufacturer photos and may not show the exact antenna layout or receiver antenna length of every available variant.

If you are not sure which version matches your radio controller, please contact us before ordering.

Product Images and Variant Notice

Product images are for display and reference only. Some images may be generic manufacturer photos and may not show the exact antenna layout, receiver antenna length, battery mounting, GPS position, props, LED appearance, side-panel details, or small details of every available variant.

The final configuration depends on the selected receiver version, production batch, and product variant.

Battery Recommendations

This drone is designed for 6S batteries and 7.5-inch long-range battery setups.

Standard LiPo recommendation:

6S 3300–3500mAh LiPo

This is the recommended starting range for a balanced mix of throttle response, manageable weight, stable handling, and practical flight time.

Larger LiPo options:

6S 4000–6000mAh LiPo can be used depending on the desired flight time and use case, but larger LiPo batteries increase takeoff weight and reduce agility.

Li-Ion / endurance cruising:

6S1P 5000mAh Li-Ion is the bare minimum Li-Ion option for this platform. It can be used for very smooth cruising only.

For 7-inch and 7.5-inch long-range platforms, we recommend 6S2P Li-Ion batteries for better throttle response and reduced voltage sag.

Recommended Li-Ion options:

6S2P 8000mAh Li-Ion for long-range endurance cruising

6S2P 10000mAh Li-Ion for maximum range and maximum endurance setups

Important Li-Ion Note:

Compared with 5-inch platforms, 7-inch and 7.5-inch drones draw more power and place higher load on the battery during climbs, wind correction, heavier payloads, and long-distance flights.

A 6S1P Li-Ion pack can experience more voltage sag and weaker throttle response on this size of drone. For this reason, 6S2P Li-Ion packs are strongly recommended when using Li-Ion on the CineLR 7.

Li-Ion batteries are suitable for smooth cruising and endurance-oriented flying. They are not suitable for aggressive freestyle, racing, repeated hard punch-outs, or high-current flying.

Li-Ion batteries behave differently from LiPo batteries and may require adjusted Betaflight voltage warnings. Always configure warning and landing voltages according to the battery chemistry and pack used.

Important Long-Range Battery Note:

Large batteries can strongly change the handling of the drone. A heavier battery may increase cruising time but reduce agility, increase braking distance, increase motor load, and require more careful flight planning.

Always keep sufficient battery reserve for return flight, wind, altitude changes, and unexpected route changes.

Action Camera Support

The CineLR 7 can carry a GoPro or similar action camera when a compatible TPU mount is used.

Adding an action camera increases takeoff weight, changes flight behavior, increases current draw, and usually reduces flight time.

For many long-range flights, the DJI O4 Air Unit Pro onboard recording may already be sufficient, reducing the need for an additional action camera.

Recommended Accessories

Default Propeller: HQ 7.5×3×3 Propellers

Standard LiPo Battery: 6S 3300–3500mAh LiPo

Minimum Li-Ion Battery: DOGCOM 6S1P 5000mAh Li-Ion Battery, smooth cruising only

Recommended Li-Ion Battery: 6S2P 8000mAh Li-Ion Battery

Maximum Range Li-Ion Battery: 6S2P 10000mAh Li-Ion Battery

Charger: HOTA D6 Pro 650W 1–6S Dual Channel AC/DC Smart Charger

GoPro Mount: Compatible CineLR 7 TPU action-camera mount

TPU Parts: CineLR 7 TPU Parts

ND Filters: iFlight O4 Air Unit Pro ND Filters

Technical Specifications

Product Name: CineLR 7 O4 6S HD BNF

Product Type: 7.5-inch BNF long-range cinematic FPV drone

Recommended Skill Level: Experienced FPV pilots

Video System: DJI O4 Air Unit Pro

Receiver Options: DJI FPV Controller 2 & 3, TBS Crossfire Diversity NANO RX, iFlight ELRS True Diversity RX variants, iFlight ELRS Dualband Diversity RX, depending on selected variant

Geometry: H-shaped

Frame Wheelbase: 334mm

Flight Controller: BLITZ F7 Flight Controller

ESC: BLITZ E55 4-IN-1 2–6S 55A ESC

ESC Burst Current: up to 65A, manufacturer-stated

Motor: XING2 2809 1250KV

Propellers: HQ 7.5×3×3 Propellers

Battery Input: 6S

Battery Plug: XT60

Recommended Battery Type: 6S LiPo or 6S Li-Ion, depending on use case

Recommended LiPo Battery: 6S 3300–3500mAh

Recommended Li-Ion Battery: 6S2P 8000mAh / 10000mAh for long-range endurance cruising

Minimum Li-Ion Battery: 6S1P 5000mAh for very smooth cruising only

Dimensions: 323 × 269 × 45mm

Weight: approx. 777g ±5g without battery

Approx. Takeoff Weight: approx. 1628g ±5g with 21700 6S 8000mAh battery

Maximum Speed: approx. 140km/h

Maximum Takeoff Altitude: approx. 7000m

Maximum Hover Time: approx. 18 minutes with 6S 3300mAh battery, manufacturer-stated value

Maximum Hover Time: approx. 25 minutes with 6S 8000mAh battery, manufacturer-stated value

Recommended Load: 800g, manufacturer-stated

Operating Temperature Range: -20°C to 40°C

Antennas: Dual DJI O4 antennas plus receiver antennas depending on selected receiver version

GPS: Pre-installed

GNSS